View MSK5215-19_759110.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ISO-9001 CERTIFIED BY DSCC
M.S.KENNEDY CORP. FEATURES:
HIGH CURRENT, LOW DROPOUT SURFACE MOUNT VOLTAGE REGULATORS
5215
SERIES
(315) 701-6751
4707 Dey Road Liverpool, N.Y. 13088
MIL-PRF-38534 CERTIFIED
Hermetic Surface Mount Package Extremely Low Dropout Voltage: 350mV @ 1.5 Amps Available in 1.5V, 1.7V, 1.9V, 2.5V, 3.3V, 5.0V and 12.0V On Board Thermal Shut Down Reverse Battery and Load Dump Protection Low Ground Current: 32mA Typical at Full Load 1% Maximum Guaranteed Accuracy Output Current to 1.5 Amps Alternate Output Voltages Available
DESCRIPTION:
The MSK 5215 series voltage regulators are available in +1.5V, +1.7V, +1.9V, +2.5V, +3.3V, +5.0V, and +12.0V output configurations. All boast ultra low dropout specifications due to the utilization of a super PNP output pass transistor with monolithic technology. Dropout voltages of 350mV at 1.5 amps are typical in this configuration, which drives efficiency up and power dissipation down. Accuracy is guaranteed with a 1% maximum output voltage tolerance. The MSK 5215 series is packaged in a space efficient 3 pin power surface mount ceramic package.
EQUIVALENT SCHEMATIC
TYPICAL APPLICATIONS
High Efficiency, High Current Linear Regulators Constant Voltage/Current Regulators System Power Supplies Switching Power Supply Post Regulators Battery Powered Equipment
1
PIN-OUT INFORMATION
1 VIN 2 VOUT 3 Ground
Rev. E 11/04
ABSOLUTE MAXIMUM RATINGS
VINP VIN VEN IOUT Input Voltage (100mS 1%D.C.) -20V to +60V Input Voltage 26V Enable Voltage -0.3V to 26V Output Current 3.5A

TST TLD TJ
Storage Temperature Range Lead Temperature . . . . . . . (10 Seconds Soldering) Operating Temperature MSK 5215 Series . . . . . . . MSK 5215H/E Series . . . .
. . -65C to +150C ..........300C
. . . -40C to +85C . . . . -55C to +125C
ELECTRICAL SPECIFICATIONS
Parameter Test Conditions 13 Group A Subgroup 1 IOUT = 10mA; VIN = VOUT +1V 2, 3 Dropout Voltage 2 VOUT = -1%; IOUT = 100 mA VOUT = -1%; IOUT = 1.5A Load Regulation 8 10 mA IOUT 1.25A (VOUT +1V) VIN 26V IOUT = 10 mA Output Current Limit 2 Ground Current Output Noise 2 Thermal Resistance 2 Thermal Shutdown 2 2 VOUT = 0V; VIN = VOUT +1V VIN = VOUT +1V; IOUT = 0.75A VIN = VOUT +1V; IOUT = 1.5A CL = 10F; 10 HZ f 100 KHZ Junction to Case @ 125C TJ 1 1 1 2, 3 Line Regulation 1 2, 3 1.0 80 350 0.2 0.3 0.05 0.5 2.1 18 32 400 3.5 130 2.0 200 600 1.0 2.0 0.5 1.0 3.5 30 4.0 80 350 0.2 0.3 0.05 0.5 2.1 18 32 400 3.5 130 225 625 1.2 0.6 3.5 30 4.5 % mV mV % % % % A mA mA V C/W C MSK 5215H/E SERIES Min. Typ. Max. 0.5 1.0 MSK 5215 SERIES Min. Typ. Max. 0.5 1.0
Units %
Output Voltage Tolerance
PART 7 NUMBER
MSK5215-1.5 MSK5215-1.7 MSK5215-1.9 MSK5215-2.5
OUTPUT VOLTAGE
+1.5V +1.7V +1.9V +2.5V +3.3V +5.0V +12.0V
NOTES:
MSK5215-3.3
1 Output decoupled to ground using 33F minimum capacitor unless otherwise specified. MSK5215-5.0 2 Guaranteed by design but no tested. Typical parameters are representative of actual MSK5215-12 device performance but are for reference only. 3 All output parameters are tested using a low duty cycle pulse to maintain TJ = TC. 4 Industrial grade and "E" suffix devices shall be tested to subgroup 1 unless otherwise specified. 5 Military grade devices ('H' suffix) shall be 100% tested to subgroups 1,2,3. 6 Subgroup 1 TC = +25C Subgroup 2 TJ = +125C Subgroup 3 TA = -55C 7 Please consult the factory if alternate output voltages are required. 8 Due to current limit, maximum output current may not be available at all values of VIN-VOUT and temperatures. See typical performance curves for clarification.
2
Rev. E 11/04
APPLICATION NOTES REGULATOR PROTECTION:
The MSK 5215 series is fully protected against reversed input polarity, overcurrent faults, overtemperature conditions (Pd) and transient voltage spikes of up to 60V. If the regulator is used in dual supply systems where the load is returned to a negative supply, the output voltage must be diode clamped to ground.
PACKAGE CONNECTIONS:
The MSK 5215 series are highly thermally conductive devices and the thermal path from the package heat sink to the internal junctions is very short. Standard surface mount soldering techniques should be used when mounting the device. Some applications may require additional heat sinking of the device.
OUTPUT CAPACITOR:
The output voltage ripple of the MSK 5215 series voltage regulators can be minimized by placing a filter capacitor from the output to ground. The optimum value for this capacitor may vary from one application to the next, but a minimum of 33F is recommended for optimum performance. Transient load response can also be improved by placing a capacitor directly across the load. The capacitor should not be an ultra-low ESR type. Tantalum capacitors are best for fast load transients but aluminum electrolytics will work fine in most applications.
HEAT SINK SELECTION:
To select a heat sink for the MSK 5215, the following formula for convective heat flow may be used. Governing Equation: Tj = Pd x (Rjc + Rcs + Rsa) + Ta WHERE: Tj = Junction Temperature Pd = Total Power Dissipation Rjc = Junction to Case Thermal Resistance Rcs = Case to Heat Sink Thermal Resistance Rsa = Heat Sink to Ambient Thermal Resistance Ta = Ambient Temperature First, the power dissipation must be calculated as follows: Power Dissipation = (Vin - Vout) x Iout Next, the user must select a maximum junction temperature. The absolute maximum allowable junction temperature is 125C. The equation may now be rearranged to solve for the required heat sink to ambient thermal resistance (Rsa). EXAMPLE: An MSK 5215-3.3 is configured for Vin=+5V and Vout=+3.3V. Iout is a continuous 1A DC level. The ambient temperature is +25C. The maximum desired junction temperature is 125C. Rjc = 3.5C/W and Rcs = 0.5C/W typically. Power Dissipation = (5V - 3.3V) x (1A) = 1.7 Watts Solve for Rsa: Rsa =
LOAD CONNECTIONS:
In voltage regulator applications where very large load currents are present, the load connection is very important. The path connecting the output of the regulator to the load must be extremely low impedance to avoid affecting the load regulation specifications. Any impedance in this path will form a voltage divider with the load.
MINIMIZING POWER DISSIPATION:
Many applications can not take full advantage of the extremely low dropout specifications of the regulator due to large input to output voltage differences. The simple circuit below illustrates a method to reduce the input voltage at the regulator to just over the dropout specification to keep the internal power dissipation minimized:
[125C - 25C] 1.7W
- 3.5C/W - 0.5C/W
For a given continuous maximum load of 1 amp, R1 can be selected to drop the voltage seen at the regulator to 4V. This allows for the output tolerance and dropout specifications. Input voltage variations (5V) also should be included in the calculations. The resistor should be sized according to the power levels required for the application.
= 54.82C/W In this example, a heat sink with a thermal resistance of no more than 54C/W must be used to maintain a junction temperature of no more than 125C.
3
Rev. E 11/04
TYPICAL PERFORMANCE CURVES
4
Rev. E 11/04
MECHANICAL SPECIFICATIONS
NOTE: ALL DIMENSIONS ARE 0.010 INCHES UNLESS OTHERWISE LABELED.
ORDERING INFORMATION
MSK5215-3.3 H
SCREENING BLANK=INDUSTRIAL; E=EXTENDED RELIABILITY H=MIL-PRF-38534 CLASS H OUTPUT VOLTAGE 1.5=+1.5V; 1.7=+1.7V; 1.9=+1.9V 2.5=+2.5V; 3.3=+3.3V; 5.0=+5.0V; 12=+12.0V GENERAL PART NUMBER
The above example is a +3.3V, Military regulator.
M.S. Kennedy Corp.
4707 Dey Road, Liverpool, New York 13088 Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet.
5
Rev. E 11/04

▲Up To Search▲

Price & Availability of MSK5215-19

	To Download MSK5215-19 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .